Pay in installments of $8.25 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 6 - Aug 11
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Far Sight by Devin KnightOne of Devin Knight's most guarded secrets from his professional act is now being made available. A truly long distance, hands off mental card effect that seems totally impossible. An effect that not only baffles lay people but many magicians as well. Performer invites anyone to help. He says he will try to subliminally force that person to choose a certain card. Magician proceeds to deal 10 or 12 cards face up on the table. He points out that most of
One of Devin Knight's most guarded secrets from his professional act is now being made available.A truly long distance, hands-off mental card effect that seems totally impossible. An effect that not only baffles lay people but many magicians as well.
Performer invites anyone to help. He says he will try to subliminally force that person to choose a certain card. Magician proceeds to deal 10 or 12 cards face up on the table. He points out that most of these cards could be psychological choices. For example, one card may be the only club on the table. Another card may be the only odd value, another may be the only red court card, etc. You tell the spectator you will try to make him take a certain card while you are 15 to 20 feet away, with your back turned!
You walk to the other side of the room or stage and turn your back to the spectator. You instruct them to look over the cards and remove one. There is no funny counting, the cards are face up on the table and he just removes any one he likes. The spectator then covers the remaining cards so they can't be seen. This is all done while your back is turned. The person then covers his FREELY chosen card with his hand concealing it from view.
While still across the room, the magician picks up a magic marker and writes something on a piece of cardboard and sets it aside. You then proceed to tell the person what card you tried to influence them to take and WHY they decided on it. Only then does the spectator show the card they chose. It is the same one you wanted them to pick! Finally for a kicker finish, the cardboard is turned around and the card the person chose is written on it in large letters!
POSTIVELY NO MARKED CARDS ARE USED. NO FORCES OF ANY KIND. NO RESTRICTIONS OF ANY KIND
- No Stooges
- No Sleights
- No Mirrors
- No Duplicate Cards
- No Electronics
- No Secret Writing
- No Fishing or questions of any kind
- You never touch the cards (even secretly) after you deal them on the table.
- The whole effect is done 15 or 20 feet away from the spectator.
- A true HANDS OFF one man effect that requires no secret assistants.
Suitable for either close-up or stage.
Comes complete with cards and Devin Knight's professional presentation.
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.9 ★★★★★
Based on 16 reviews
Sort
Product Reviews
★★★★★ 5
Easy to use
Works great
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 9, 2026
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024