Pay in installments of $36.75 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 19 - Aug 24
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Skystars F7HD Stack F722HD Pro 4 Flight Controller & KM65A F4 128KHz AM32 65A 4in1 ESC - 30 x 30mmSkystars F7+KM65 is a powerful stack for 5" freestyle and racing drones or 7 8" long range drones. The flight controller with modern F7processor has 16MB memory for blackbox and 5V 3A and 10V 3A BEC. The flight controller can be conveniently used on a drone with both digital and analog video transmission. The pads for connecting the LEDs are in the corners. The integrated barometer for altitude measurement also comes in handy. The KM65 ESC supports 3
Skystars F7+KM65 is a powerful stack for 5" freestyle and racing drones or 7-8" long-range drones. The flight controller with modern F7processor has 16MB memory for blackbox and 5V/3A and 10V/3A BEC. The flight controller can be conveniently used on a drone with both digital and analog video transmission. The pads for connecting the LEDs are in the corners. The integrated barometer for altitude measurement also comes in handy.
The KM65 ESC supports 3-6S battery power and current up to 65A, which makes it playfully handle motors of size 2207-2808. The ESC has an aluminum heat sink on top to help dissipate heat better while protecting sensitive components from mechanical damage. The ESC uses a powerful F4 32-bit processor and AM32 firmware. Thus it supports telemetry, bidirectional DShot and PWM frequency up to 128KHz. The ESC is protected against voltage spikes by a TVS diode.
Check out all our Stacks and the rest of our Skystars Products!
Features:
- 1. Solder pads are the largest in size compared to other FC in market.
- 2. Proper solder pad spacing to avoid solder bridge and facilitate easy soldering.
- 3. ESC connector on top-side rather than bottom which makes it easy for repair.
- 4. TVS Diode for Reverse Polarity Protection and Voltage Spike Suppression.
- 5. Powerful 3A BEC to supply all your electronics.
- 6. Pads arrangement are executed in such a way that when you twist the wires of the camera VTX and RX you don't get any wire overlapping this gives you a uniform twist and clean look.
- 7. Support DJI O3 connector on the top side.
- 8. Support VTX ON/OFF Pit Switch.
- 9. Gyroscope independent power supply, No power lines near MPU6000 Gyro to avoid any EMI interference.
- 10. Two stages of Quality check to reduce any faulty electronic.
- 11. Comes ready with I2C support and INAV.
FC Specifications:
- MCU: STM32F722RET6 216MHz
- Gyroscope: ICM42688P
- Baro:Bmp280
- OSD: Betaflight SPI OSD DJI HD OSD(UART6)
- Black box: 16MB
- 6x Uarts: UART 1/2/3/4/5/6
- 4x PWM outputs
- 1x I2C
- 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)
- USB Type-C(USB2.0)
- 1x JST-SH1.0_8pin connector (Gnd/Vbat/S1/S2/S3/S4/Rx3/Curr)
- 1x JST-SH1.0_6pin connector (10V/Gnd/TX6/RX6/Gnd/Sbus)
- VTX 10V/Vbat filtered power ON/OFF Pit switch
- DJI FPV OSD is supported by any spare UART
- LED: 4 LED independent pads, support WS2812 programming lamp output.
- Receiver: Support Sbus, crsf, ibus, SBUS, XBUS, support 3.3v Spektrum satellite receiver, The default receiver input is UART1(You can solder ELRS RX on UART1), F7 has a built-in inverter, which can actually be installed in any spare UART.
Power:
- Input voltage: 3-6S
- BEC: 5V/10V 3A dual-channel BEC supports stable power supply on the sky side of DJI O3
- LDO 3.3V: Max.250mA
- Flight control onboard voltage sensor.
FC Firmware:
- BetaFlight firmware: SKYSTARSF722Pro
- INAV firmware:SKYSTARSF722HD
Mounting:
- Installation size: 30.5mm × 30.5mm The installation hole is M4 and supports shock column installation
- External size 39mm × 39mm
- Flight control weight: 6.9g
AM32-65A 4IN1 3-6S ESC BLheli32 128K DShot1200 4-in-1 ESC Specifications:
- Support 128K Dshot1200, Dshot600, Dshot300, Dshot150, Oneshot125, Multishot, PWM control signal
- Excellent over-current capability.
- Extreme stably support 6S LiPo battery with TVS.
- Excellent heat dissipation performance
- Better control performance F4 core MCU support 128K.
- Input voltage: 3-6S LiPo
- Con.Current: 65A
- Peak Current: 90A≥ 10S
- Firmware: AM_32
- Support : Dshot 600/1200
- Mounting hole : 30.5mm/M3
- BEC: No
- Product size: 45.6*45*7.6mm
- Weight: 19g
Package Includes:
- 1x F7HD Pro4 FC
- 1x KM65 128K AM32 4IN1 ESC
- 8x Silicon grommets M4 to M3
- 2x JST-SH1.0_8pin cable, 4cm
- 1x JST-GH-6P cable for DJI port, 10cm
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy