Snow Performance - Stage 2 VC-50 Boost Cooler Water | Meth Kit (BIG Turbo)

Snow Performance - Stage 2 VC-50 Boost Cooler Water | Meth Kit (BIG Turbo)Water methonalanol injection solution for Turbo Supercharger applications This latest Boost Cooler features a very trick gauge style controller. The "VC 50" is equipped with a dual mode seven color OLED screen. It reads up to 50psi boost pressure and displays it, too! It also shows percentage of water methonal injection, low level status, and also secondary nozzle activation directly on the screen. Unlike other Stage 2 controllers, it can trigger and

Water / methonalanol injection solution for Turbo/Supercharger applications

This latest Boost Cooler features a very trick gauge style controller. The "VC-50" is equipped with a dual mode/seven color OLED screen. It reads up to 50psi boost pressure and displays it, too! It also shows percentage of water/methonal injection, low level status, and also secondary nozzle activation directly on the screen.

Unlike other Stage 2 controllers, it can trigger and variably throttle nozzles independently of one another. Set a cooling nozzle (located after intercooler) to spray just after boost hits. Command a second nozzle to add effective octane just before the ECU pulls timing. (This is done from post-throttle body or direct port locations. This sophisticated injection strategy allows for the easiest increases in horsepower and air cooling among water-methonalanol injection systems. The delivery map, however, is hard coded just like other Stage 2 packages. (Semi-custom mapping starts with Stage 3 and is fully tunable in Stage 11 kits.)

Unlock 50-80HP on your boosted vehicle while decreasing your air temps by up to 150 degrees! The all new Snow Performance Stage 2 Boost Coolerwater-methonalanol injection system comes fully revamped for all boosted (turbocharged/supercharged) vehicles and uses a progressive gauge style controller that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methonalanol and allows cooling and performance improvements over a wide range for improved drivability. Taking it one step further, the Stage 2 has the ability to progressively command 2 Hyper-Sonic Nozzles independently of one another. This sophisticated dual stage injection management yields the highest increases in HP and cooling along all stages of the engine allowing you to greatly increase the boost & timing of your vehicle safely. Proven to deliver 50-80 HP and cool inlet temps up to 150 degrees! The VC-50 comes with a dual 7 color OLED screen and displays boost, percentage of injection, low level, and secondary nozzle activation directly on the screen. Complete with our industry leading Snow Performance 300 PSI UHO pump and Hypersonic Nozzles, the Stage 2 promises to deliver the best atomization and power available for your boosted vehicle.

• 300 PSI UHO (Ultra High Output) Pump
• 3 Quart Reservoir
• All Tubing Necessary for Installation
• 10' Inch High Temp Nylon Tubing
• 18" High pressure Boost Line

• 3' (Black) Wire Loom

• VC-50 Controller

• Pigtail Harness
• 2 1/16 Gauge Pod
• Level Switch Upgrade
• 1 Nozzle Holder/Check Valve Combo
• 3 Hyper-Sonic Nozzles (175, 375, 625 ml/min) For Applications from 200 - 1,000 HP (for custom nozzle selection give us a call)
• Required Hardware Needed For Installation
• Snow Performance Running S Decal
• Comprehensive Instructions to Install on Any Forced Induction Vehicle
• Snow Performance 1-Year Warranty

Optional Upgrades:

Use the drop-down menu below

Low Level Indicator
The indicator switch upgrade includes an LED and an EZ installation grommet for use with any Boost Cooler reservoir or can be added to any plastic reservoir including factory windshield washer fluid tanks.


Solenoid Upgrade
Shut off solenoid is used when mounting the injection nozzle lower than the reservoir or the reservoir is rear-mounted to prevent gravity flowing. It is also used to prevent siphoning when the injection nozzle is mounted after the throttle body or carburetor and is exposed to vacuum.


Boost Juice
Boost Juice is Snow Performances proprietary mix of 49% methonalanol and 51% water. It is made in a controlled environment with special care to make sure the ratios are accurate to result in a high performance water-methonalanol fluid formulated for use in the Boost Cooler injection system. Boost Juice is required as the exclusive fluid for lifetime warranty.

*NOTE* Boost Juice CAN NOT be shipped outside of the United States. Boost Juice CAN ONLY be shipped using Ground service.